--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Commit 3073677b8280e94256db24d147bfc7d383808750
Parents : 2119d38
Author : Mark Qvist <mark@unsigned.io>
Date : 2025-01-15T11:01:26+01:00
Added sleep and wake support on T114
Changes
Diff
diff --git a/RNode_Firmware.ino b/RNode_Firmware.ino
index 245e55a..d3f5aba 100644
--- a/RNode_Firmware.ino
+++ b/RNode_Firmware.ino
@@ -105,7 +105,7 @@ void setup() {
led_init();
#endif
- #if BOARD_MODEL != BOARD_RAK4631 && BOARD_MODEL != BOARD_HELTEC_T114 && BOARD_MODEL != BOARD_RNODE_NG_22 && BOARD_MODEL != BOARD_TBEAM_S_V1
+ #if BOARD_MODEL != BOARD_RAK4631 && BOARD_MODEL != BOARD_HELTEC_T114 && BOARD_MODEL != BOARD_T3S3 && BOARD_MODEL != BOARD_TBEAM_S_V1
// Some boards need to wait until the hardware UART is set up before booting
// the full firmware. In the case of the RAK4631 and Heltec T114, the line below will wait
// until a serial connection is actually established with a master. Thus, it
@@ -161,7 +161,7 @@ void setup() {
#if MCU_VARIANT == MCU_ESP32 || MCU_VARIANT == MCU_NRF52
init_channel_stats();
- #if BOARD_MODEL == BOARD_RNODE_NG_22
+ #if BOARD_MODEL == BOARD_T3S3
#if MODEM == SX1280
delay(300);
LoRa->reset();
@@ -246,7 +246,7 @@ void setup() {
if (ia_conf == 0x00) { avoid_interference = true; }
else { avoid_interference = false; }
#elif MCU_VARIANT == MCU_NRF52
- uint8_t ia_conf == eeprom_read(eeprom_addr(ADDR_CONF_DIA));
+ uint8_t ia_conf = eeprom_read(eeprom_addr(ADDR_CONF_DIA));
if (ia_conf == 0x00) { avoid_interference = true; }
else { avoid_interference = false; }
#endif
@@ -1592,22 +1592,34 @@ void loop() {
void sleep_now() {
#if HAS_SLEEP == true
- #if BOARD_MODEL == BOARD_RNODE_NG_22
- display_intensity = 0;
- update_display(true);
- #endif
- #if PIN_DISP_SLEEP >= 0
- pinMode(PIN_DISP_SLEEP, OUTPUT);
- digitalWrite(PIN_DISP_SLEEP, DISP_SLEEP_LEVEL);
- #endif
- #if HAS_BLUETOOTH
- if (bt_state == BT_STATE_CONNECTED) {
- bt_stop();
- delay(100);
- }
+ #if PLATFORM == PLATFORM_ESP32
+ #if BOARD_MODEL == BOARD_T3S3
+ display_intensity = 0;
+ update_display(true);
+ #endif
+ #if PIN_DISP_SLEEP >= 0
+ pinMode(PIN_DISP_SLEEP, OUTPUT);
+ digitalWrite(PIN_DISP_SLEEP, DISP_SLEEP_LEVEL);
+ #endif
+ #if HAS_BLUETOOTH
+ if (bt_state == BT_STATE_CONNECTED) {
+ bt_stop();
+ delay(100);
+ }
+ #endif
+ esp_sleep_enable_ext0_wakeup(PIN_WAKEUP, WAKEUP_LEVEL);
+ esp_deep_sleep_start();
+ #elif PLATFORM == PLATFORM_NRF52
+ #if BOARD_MODEL == BOARD_HELTEC_T114
+ npset(0,0,0);
+ digitalWrite(PIN_T114_VEXT_EN, LOW);
+ digitalWrite(PIN_T114_TFT_BLGT, HIGH);
+ digitalWrite(PIN_T114_TFT_EN, HIGH);
+ #endif
+ sd_power_gpregret_set(0, 0x6d);
+ nrf_gpio_cfg_sense_input(pin_btn_usr1, NRF_GPIO_PIN_PULLUP, NRF_GPIO_PIN_SENSE_LOW);
+ NRF_POWER->SYSTEMOFF = 1;
#endif
- esp_sleep_enable_ext0_wakeup(PIN_WAKEUP, WAKEUP_LEVEL);
- esp_deep_sleep_start();
#endif
}
──────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────